Table of contents
CSPICE_GFSUBC determines the time intervals for which a coordinate
of an subpoint position vector satisfies a numerical constraint.
Given:
target the name of the target body.
[1,c1] = size(target); char = class(target)
or
[1,1] = size(target); cell = class(target)
Optionally, you may supply the integer ID code for the object
as an integer string. For example both 'MOON' and '301'
are legitimate strings that indicate the Moon is the
target body.
On calling cspice_gfsubc, the kernel pool must contain the
radii data corresponding to `target'.
fixref the name of the body-fixed, body-centered
reference frame associated with the target body `target'.
[1,c2] = size(fixref); char = class(fixref)
or
[1,1] = size(fixref); cell = class(fixref)
The SPICE frame subsystem must recognize the `fixref' name.
method the name of the method to use for the subpoint
calculation.
[1,c3] = size(method); char = class(method)
or
[1,1] = size(method); cell = class(method)
The accepted values for method:
'Near point: ellipsoid' The sub-observer point
computation uses a
triaxial ellipsoid to
model the surface of the
target body. The
sub-observer point is
defined as the nearest
point on the target
relative to the
observer.
'Intercept: ellipsoid' The sub-observer point
computation uses a
triaxial ellipsoid to
model the surface of the
target body. The
sub-observer point is
defined as the target
surface intercept of the
line containing the
observer and the
target's center.
The `method' string lacks sensitivity to case, and to
embedded, leading and trailing blanks.
abcorr describes the aberration corrections to apply to the state
evaluations to account for one-way light time and stellar
aberration.
[1,c4] = size(abcorr); char = class(abcorr)
or
[1,1] = size(abcorr); cell = class(abcorr)
This routine accepts the same aberration corrections as does
the routine cspice_spkezr. See the header of cspice_spkezr for
a detailed description of the aberration correction options.
For convenience, the options are listed below:
'NONE' Apply no correction.
'LT' "Reception" case: correct for
one-way light time using a Newtonian
formulation.
'LT+S' "Reception" case: correct for
one-way light time and stellar
aberration using a Newtonian
formulation.
'CN' "Reception" case: converged
Newtonian light time correction.
'CN+S' "Reception" case: converged
Newtonian light time and stellar
aberration corrections.
'XLT' "Transmission" case: correct for
one-way light time using a Newtonian
formulation.
'XLT+S' "Transmission" case: correct for
one-way light time and stellar
aberration using a Newtonian
formulation.
'XCN' "Transmission" case: converged
Newtonian light time correction.
'XCN+S' "Transmission" case: converged
Newtonian light time and stellar
aberration corrections.
The `abcorr' string lacks sensitivity to case, and to
embedded, leading and trailing blanks.
obsrvr the name of the observing body.
[1,c5] = size(obsrvr); char = class(obsrvr)
or
[1,1] = size(obsrvr); cell = class(obsrvr)
Optionally, you may supply the ID code of the object as an
integer string. For example, both 'EARTH' and '399' are
legitimate strings to supply to indicate the observer
is the Earth.
crdsys the name of the coordinate system for which the
coordinate of interest is a member.
[1,c6] = size(crdsys); char = class(crdsys)
or
[1,1] = size(crdsys); cell = class(crdsys)
coord the name of the coordinate of interest in `crdsys'.
[1,c7] = size(coord); char = class(coord)
or
[1,1] = size(coord); cell = class(coord)
The supported coordinate systems and coordinate names are:
crdsys coord Range
------------------ ------------------- ------------
'RECTANGULAR' 'X'
'Y'
'Z'
'LATITUDINAL' 'RADIUS'
'LONGITUDE' (-Pi,Pi]
'LATITUDE' [-Pi/2,Pi/2]
'RA/DEC' 'RANGE'
'RIGHT ASCENSION' [0,2Pi)
'DECLINATION' [-Pi/2,Pi/2]
'SPHERICAL' 'RADIUS'
'COLATITUDE' [0,Pi]
'LONGITUDE' (-Pi,Pi]
'CYLINDRICAL' 'RADIUS'
'LONGITUDE' [0,2Pi)
'Z'
'GEODETIC' 'LONGITUDE' (-Pi,Pi]
'LATITUDE' [-Pi/2,Pi/2]
'ALTITUDE'
'PLANETOGRAPHIC' 'LONGITUDE' [0,2Pi)
'LATITUDE' [-Pi/2,Pi/2]
'ALTITUDE'
The ALTITUDE coordinates have a constant value
of zero +/- roundoff for ellipsoid targets.
Limit searches for coordinate events in the GEODETIC and
PLANETOGRAPHIC coordinate systems to `target' bodies with
axial symmetry in the equatorial plane, i.e. equality
of the body X and Y radii (oblate or prolate spheroids).
relate the constraint relational operator on the selected coordinate
of the subpoint vector.
[1,c8] = size(relate); char = class(relate)
or
[1,1] = size(relate); cell = class(relate)
The result window found by this routine indicates the time
intervals where the constraint is satisfied.
Supported values of `relate' and corresponding meanings are
shown below:
'>' Separation is greater than the reference
value `refval'.
'=' Separation is equal to the reference
value `refval'.
'<' Separation is less than the reference
value `refval'.
'ABSMAX' Separation is at an absolute maximum.
'ABSMIN' Separation is at an absolute minimum.
'LOCMAX' Separation is at a local maximum.
'LOCMIN' Separation is at a local minimum.
The caller may indicate that the region of interest
is the set of time intervals where the quantity is
within a specified measure of an absolute extremum.
The argument `adjust' (described below) is used to
specify this measure.
Local extrema are considered to exist only in the
interiors of the intervals comprising the confinement
window: a local extremum cannot exist at a boundary
point of the confinement window.
The `relate' string lacks sensitivity to case, and to leading
and trailing blanks.
refval reference value used together with `relate' argument to define
an equality or inequality to satisfy the selected coordinate
of the subpoint vector.
[1,1] = size(refval); double = class(refval)
See the discussion of `relate' above for further information.
The units of `refval' correspond to the type as defined
by `coord', radians for angular measures, kilometers for
distance measures.
adjust value used to modify searches for absolute extrema.
[1,1] = size(adjust); double = class(adjust)
When `relate' is set to 'ABSMAX' or 'ABSMIN' and `adjust' is
set to a positive value, cspice_gfsubc finds times when the
subpoint vector coordinate is within `adjust'
radians/kilometers of the specified extreme value.
For `relate' set to 'ABSMAX', the result window contains
time intervals when the subpoint vector coordinate has
values between ABSMAX - adjust and ABSMAX.
For `relate' set to 'ABSMIN', the result window contains
time intervals when the position vector coordinate has
values between ABSMIN and ABSMIN + adjust.
`adjust' is not used for searches for local extrema,
equality or inequality conditions.
step time step size to use in the search.
[1,1] = size(adjust); double = class(adjust)
`step' must be short enough to for a search using this step
size to locate the time intervals where coordinate
function of the subpoint vector is monotone increasing or
decreasing. However, `step' must not be *too* short, or
the search will take an unreasonable amount of time.
For coordinates other than LONGITUDE and RIGHT ASCENSION,
the step size must be shorter than the shortest interval,
within the confinement window, over which the coordinate
is monotone increasing or decreasing.
For LONGITUDE and RIGHT ASCENSION, the step size must
be shorter than the shortest interval, within the
confinement window, over which either the sin or cos
of the coordinate is monotone increasing or decreasing.
The choice of `step' affects the completeness but not
the precision of solutions found by this routine; the
precision is controlled by the convergence tolerance.
See the discussion of the parameter SPICE_GF_CNVTOL for
details.
`step' has units of TDB seconds.
nintvls value specifying the number of intervals in the internal
workspace array used by this routine.
[1,1] = size(nintvls); int32 = class(nintvls)
`nintvls' should be at least as large as the number of
intervals within the search region on which the specified
observer-target vector coordinate function is monotone
increasing or decreasing. It does no harm to pick a value
of `nintvls' larger than the minimum required to execute
the specified search, but if chosen too small, the search
will fail.
cnfine a SPICE window that confines the time period over which the
specified search is conducted.
[2m,1] = size(cnfine); double = class(cnfine)
`cnfine' may consist of a single interval or a collection of
intervals.
In some cases the confinement window can be used to
greatly reduce the time period that must be searched
for the desired solution. See the -Particulars section
below for further discussion.
See the -Examples section below for a code example
that shows how to create a confinement window.
In some cases the observer's state may be computed at
times outside of `cnfine' by as much as 2 seconds. See
-Particulars for details.
the call:
[result] = cspice_gfsubc( target, fixref, method, abcorr, obsrvr, ...
crdsys, coord, relate, refval, ...
adjust, step, nintvls, cnfine )
returns:
result the SPICE window of intervals, contained within the
confinement window `cnfine', on which the specified
constraint is satisfied.
[2n,1] = size(result); double = class(result)
If the search is for local extrema, or for absolute
extrema with `adjust' set to zero, then normally each
interval of `result' will be a singleton: the left and
right endpoints of each interval will be identical.
If no times within the confinement window satisfy the
constraint, `result' will return with cardinality zero.
All parameters described here are declared in the Mice include file
MiceGF.m. See that file for parameter values.
SPICE_GF_CNVTOL
is the convergence tolerance used for finding endpoints
of the intervals comprising the result window.
SPICE_GF_CNVTOL is used to determine when binary
searches for roots should terminate: when a root is
bracketed within an interval of length SPICE_GF_CNVTOL,
the root is considered to have been found.
The accuracy, as opposed to precision, of roots found
by this routine depends on the accuracy of the input
data. In most cases, the accuracy of solutions will be
inferior to their precision.
Any numerical results shown for this example may differ between
platforms as the results depend on the SPICE kernels used as input
and the machine specific arithmetic implementation.
1) Find the time during 2007 for which the subpoint position vector
of the sun on earth in the IAU_EARTH frame lies within a geodetic
latitude-longitude "box" defined as
16 degrees <= latitude <= 17 degrees
85 degrees <= longitude <= 86 degrees
This problem requires four searches, each search on one of the
box restrictions. The user needs also realize the temporal
behavior of latitude greatly differs from that of the longitude. The
sub-observer point latitude varies between approximately 23.44 degrees
and -23.44 degrees during the year. The sub-observer point longitude
varies between -180 degrees and 180 degrees in one day.
Use the meta-kernel shown below to load the required SPICE
kernels.
KPL/MK
File name: gfsubc_ex1.tm
This meta-kernel is intended to support operation of SPICE
example programs. The kernels shown here should not be
assumed to contain adequate or correct versions of data
required by SPICE-based user applications.
In order for an application to use this meta-kernel, the
kernels referenced here must be present in the user's
current working directory.
The names and contents of the kernels referenced
by this meta-kernel are as follows:
File name Contents
--------- --------
de414.bsp Planetary ephemeris
pck00008.tpc Planet orientation and
radii
naif0008.tls Leapseconds
\begindata
KERNELS_TO_LOAD = ( 'de414.bsp',
'pck00008.tpc',
'naif0008.tls' )
\begintext
End of meta-kernel
Example code begins here.
function gfsubc_ex1()
MAXWIN = 1000;
TIMFMT = 'YYYY-MON-DD HR:MN:SC.###### (TDB) ::TDB ::RND';
R2D = cspice_dpr;
%
% Load kernels.
%
cspice_furnsh( 'gfsubc_ex1.tm' );
%
% Store the time bounds of our search interval in
% the cnfine confinement window.
%
et = cspice_str2et( { '2007 JAN 01', '2008 JAN 01'} );
cnfine = cspice_wninsd( et(1), et(2) );
%
% The latitude varies relatively slowly (46 degrees) during the
% year. The extrema occur approximately every six months.
% Search using a step size less than half that value (180 days).
% For this example use ninety days (in units of seconds).
%
step = cspice_spd*90.;
%
% Perform four searches to determine the times when the latitude-
% longitude box restriction conditions apply to the subpoint vector.
%
% Use geodetic coordinates.
%
adjust = 0.;
target = 'EARTH';
obsrvr = 'SUN';
method = 'Near point: ellipsoid';
fixref = 'IAU_EARTH';
crdsys = 'GEODETIC';
nintvls= MAXWIN;
abcorr = 'NONE';
%
% Perform the searches such that the result window of a search
% serves as the confinement window of the subsequent search.
%
%
% Since the latitude coordinate varies slowly and is well behaved
% over the time of the confinement window, search first for the
% windows satisfying the latitude requirements, then use that result
% as confinement for the longitude search.
%
coord = 'LATITUDE';
refval = 16. * cspice_rpd;
relate = '>';
%
% Perform this search using the geometric position
% of the bodies; set the aberration correction to 'NONE'.
%
result1 = cspice_gfsubc( target, fixref, method, abcorr, ...
obsrvr, crdsys, coord, ...
relate, refval, adjust, ...
step, nintvls, cnfine );
refval = 17. * cspice_rpd;
relate = '<';
result2 = cspice_gfsubc( target, fixref, method, abcorr, ...
obsrvr, crdsys, coord, ...
relate, refval, adjust, ...
step, nintvls, result1 );
%
% Now the longitude search.
%
coord = 'LONGITUDE';
%
% Reset the step size to something appropriate for the 360
% degrees in 24 hours domain. The longitude shows near
% linear behavior so use a step size less than half the period
% of twelve hours. Ten hours will suffice in this case.
%
step = cspice_spd * (10./24.);
refval = 85. * cspice_rpd;
relate = '>';
result3 = cspice_gfsubc( target, fixref, method, abcorr, ...
obsrvr, crdsys, coord, ...
relate, refval, adjust, ...
step, nintvls, result2 );
%
% Contract the endpoints of each window to account
% for possible round-off error at the -180/180 degree branch.
%
% A contraction value of a millisecond should eliminate
% any round-off caused branch crossing.
%
result3 = cspice_wncond( 1e-3, 1e-3, result3 );
refval = 86. * cspice_rpd;
relate = '<';
result4 = cspice_gfsubc( target, fixref, method, abcorr, ...
obsrvr, crdsys, coord, ...
relate, refval, adjust, ...
step, nintvls, result3 );
result = result4;
for i=1:numel(result)/2
[left, right] = cspice_wnfetd( result, i );
output = cspice_timout( [left,right], TIMFMT );
if( isequal( left, right) )
disp( ['Event time: ' output(1,:)] )
else
[lspoint, trgepc, srfvec] = cspice_subpnt(method, target, ...
left, fixref, ...
abcorr, obsrvr);
[lrad, llong, llat ] = cspice_reclat( lspoint );
[rspoint, trgepc, srfvec] = cspice_subpnt(method, target, ...
right, fixref, ...
abcorr, obsrvr);
[rrad, rlong, rlat ] = cspice_reclat( rspoint );
fprintf( 'From : %s %f %f\n', output(1,:), ...
llat*R2D, ...
llong*R2D )
fprintf( 'To : %s %f %f\n', output(2,:), ...
rlat*R2D, ...
rlong*R2D )
fprintf( '\n' );
end
end
%
% It's always good form to unload kernels after use,
% particularly in Matlab due to data persistence.
%
cspice_kclear
When this program was executed on a Mac/Intel/Octave6.x/64-bit
platform, the output was:
From : 2007-MAY-05 06:14:04.637735 (TDB) 16.054356 86.000000
To : 2007-MAY-05 06:18:04.621907 (TDB) 16.055148 85.000004
From : 2007-MAY-06 06:13:59.583483 (TDB) 16.337147 86.000000
To : 2007-MAY-06 06:17:59.569240 (TDB) 16.337927 85.000004
From : 2007-MAY-07 06:13:55.102940 (TDB) 16.615444 86.000000
To : 2007-MAY-07 06:17:55.090299 (TDB) 16.616210 85.000004
From : 2007-MAY-08 06:13:51.202604 (TDB) 16.889163 86.000000
To : 2007-MAY-08 06:17:51.191583 (TDB) 16.889916 85.000004
From : 2007-AUG-06 06:23:17.282927 (TDB) 16.680717 86.000000
To : 2007-AUG-06 06:27:17.264010 (TDB) 16.679962 85.000004
From : 2007-AUG-07 06:23:10.545441 (TDB) 16.406411 86.000000
To : 2007-AUG-07 06:27:10.524925 (TDB) 16.405643 85.000004
From : 2007-AUG-08 06:23:03.233996 (TDB) 16.127678 86.000000
To : 2007-AUG-08 06:27:03.211889 (TDB) 16.126897 85.000004
This routine determines a set of one or more time intervals
within the confinement window when the selected coordinate of
the subpoint position vector satisfies a caller-specified
constraint. The resulting set of intervals is returned as a SPICE
window.
Below we discuss in greater detail aspects of this routine's
solution process that are relevant to correct and efficient
use of this routine in user applications.
The Search Process
==================
Regardless of the type of constraint selected by the caller, this
routine starts the search for solutions by determining the time
periods, within the confinement window, over which the specified
coordinate function is monotone increasing and monotone
decreasing. Each of these time periods is represented by a SPICE
window. Having found these windows, all of the coordinate
function's local extrema within the confinement window are known.
Absolute extrema then can be found very easily.
Within any interval of these "monotone" windows, there will be at
most one solution of any equality constraint. Since the boundary
of the solution set for any inequality constraint is contained in
the union of
- the set of points where an equality constraint is met
- the boundary points of the confinement window
the solutions of both equality and inequality constraints can be
found easily once the monotone windows have been found.
Step Size
=========
The monotone windows (described above) are found using a two-step
search process. Each interval of the confinement window is
searched as follows: first, the input step size is used to
determine the time separation at which the sign of the rate of
change of coordinate will be sampled. Starting at
the left endpoint of an interval, samples will be taken at each
step. If a change of sign is found, a root has been bracketed; at
that point, the time at which the time derivative of the
coordinate is zero can be found by a refinement process, for
example, using a binary search.
Note that the optimal choice of step size depends on the lengths
of the intervals over which the coordinate function is monotone:
the step size should be shorter than the shortest of these
intervals (within the confinement window).
The optimal step size is *not* necessarily related to the lengths
of the intervals comprising the result window. For example, if
the shortest monotone interval has length 10 days, and if the
shortest result window interval has length 5 minutes, a step size
of 9.9 days is still adequate to find all of the intervals in the
result window. In situations like this, the technique of using
monotone windows yields a dramatic efficiency improvement over a
state-based search that simply tests at each step whether the
specified constraint is satisfied. The latter type of search can
miss solution intervals if the step size is longer than the
shortest solution interval.
Having some knowledge of the relative geometry of the target and
observer can be a valuable aid in picking a reasonable step size.
In general, the user can compensate for lack of such knowledge by
picking a very short step size; the cost is increased computation
time.
Note that the step size is not related to the precision with which
the endpoints of the intervals of the result window are computed.
That precision level is controlled by the convergence tolerance.
Convergence Tolerance
=====================
As described above, the root-finding process used by this routine
involves first bracketing roots and then using a search process
to locate them. "Roots" are both times when local extrema are
attained and times when the coordinate function is equal to a
reference value. All endpoints of the intervals comprising the
result window are either endpoints of intervals of the
confinement window or roots.
Once a root has been bracketed, a refinement process is used to
narrow down the time interval within which the root must lie.
This refinement process terminates when the location of the root
has been determined to within an error margin called the
"convergence tolerance." The default convergence tolerance
used by this routine is set by the parameter SPICE_GF_CNVTOL (defined
in MiceGF.m).
The value of SPICE_GF_CNVTOL is set to a "tight" value so that the
tolerance doesn't become the limiting factor in the accuracy of
solutions found by this routine. In general the accuracy of input
data will be the limiting factor.
The user may change the convergence tolerance from the default
SPICE_GF_CNVTOL value by calling the routine cspice_gfstol, e.g.
cspice_gfstol( tolerance value );
Call cspice_gfstol prior to calling this routine. All subsequent
searches will use the updated tolerance value.
Setting the tolerance tighter than SPICE_GF_CNVTOL is unlikely to be
useful, since the results are unlikely to be more accurate.
Making the tolerance looser will speed up searches somewhat,
since a few convergence steps will be omitted. However, in most
cases, the step size is likely to have a much greater effect
on processing time than would the convergence tolerance.
The Confinement Window
======================
The simplest use of the confinement window is to specify a time
interval within which a solution is sought. However, the
confinement window can, in some cases, be used to make searches
more efficient. Sometimes it's possible to do an efficient search
to reduce the size of the time period over which a relatively
slow search of interest must be performed.
Practical use of the coordinate search capability would likely
consist of searches over multiple coordinate constraints to find
time intervals that satisfies the constraints. An
effective technique to accomplish such a search is
to use the result window from one search as the confinement window
of the next.
Certain types of searches require the state of the observer,
relative to the solar system barycenter, to be computed at times
slightly outside the confinement window `cnfine'. The time window
that is actually used is the result of "expanding" `cnfine' by a
specified amount "T": each time interval of `cnfine' is expanded by
shifting the interval's left endpoint to the left and the right
endpoint to the right by T seconds. Any overlapping intervals are
merged. (The input argument `cnfine' is not modified.)
The window expansions listed below are additive: if both
conditions apply, the window expansion amount is the sum of the
individual amounts.
- If a search uses an equality constraint, the time window
over which the state of the observer is computed is expanded
by 1 second at both ends of all of the time intervals
comprising the window over which the search is conducted.
- If a search uses stellar aberration corrections, the time
window over which the state of the observer is computed is
expanded as described above.
When light time corrections are used, expansion of the search
window also affects the set of times at which the light time-
corrected state of the target is computed.
In addition to the possible 2 second expansion of the search
window that occurs when both an equality constraint and stellar
aberration corrections are used, round-off error should be taken
into account when the need for data availability is analyzed.
Longitude and Right Ascension
=============================
The cyclic nature of the longitude and right ascension coordinates
produces branch cuts at +/- 180 degrees longitude and 0-360
longitude. Round-off error may cause solutions near these branches
to cross the branch. Use of the Mice routine cspice_wncond will contract
solution windows by some epsilon, reducing the measure of the
windows and eliminating the branch crossing. A one millisecond
contraction will in most cases eliminate numerical round-off
caused branch crossings.
1) In order for this routine to produce correct results,
the step size must be appropriate for the problem at hand.
Step sizes that are too large may cause this routine to miss
roots; step sizes that are too small may cause this routine
to run unacceptably slowly and in some cases, find spurious
roots.
This routine does not diagnose invalid step sizes, except
that if the step size is non-positive, an error is signaled
by a routine in the call tree of this routine.
2) Due to numerical errors, in particular,
- truncation error in time values
- finite tolerance value
- errors in computed geometric quantities
it is *normal* for the condition of interest to not always be
satisfied near the endpoints of the intervals comprising the
`result' window. One technique to handle such a situation,
slightly contract `result' using the window routine cspice_wncond.
3) If the output SPICE window `result' has insufficient capacity
to contain the number of intervals on which the specified
distance condition is met, an error is signaled
by a routine in the call tree of this routine.
4) If an error (typically cell overflow) occurs during
window arithmetic, the error is signaled by a routine
in the call tree of this routine.
5) If the relational operator `relate' is not recognized, an
error is signaled by a routine in the call tree of this
routine.
6) If the aberration correction specifier contains an
unrecognized value, an error is signaled by a routine in the
call tree of this routine.
7) If `adjust' is negative, an error is signaled by a routine in
the call tree of this routine.
8) If either of the input body names do not map to NAIF ID
codes, an error is signaled by a routine in the call tree of
this routine.
9) If required ephemerides or other kernel data are not
available, an error is signaled by a routine in the call tree
of this routine.
10) If the search uses GEODETIC or PLANETOGRAPHIC coordinates, and
the center body of the reference frame has unequal equatorial
radii, an error is signaled by a routine in the call tree of
this routine.
11) If any of the input arguments, `target', `fixref', `method',
`abcorr', `obsrvr', `crdsys', `coord', `relate', `refval',
`adjust', `step', `nintvls' or `cnfine', is undefined, an
error is signaled by the Matlab error handling system.
12) If any of the input arguments, `target', `fixref', `method',
`abcorr', `obsrvr', `crdsys', `coord', `relate', `refval',
`adjust', `step', `nintvls' or `cnfine', is not of the
expected type, or it does not have the expected dimensions and
size, an error is signaled by the Mice interface.
Appropriate SPK and PCK kernels must be loaded by the calling
program before this routine is called.
The following data are required:
- SPK data: the calling application must load ephemeris data
for the targets, observer, and any intermediate objects in
a chain connecting the targets and observer that cover the
time period specified by the window `cnfine'. If aberration
corrections are used, the states of target and observer
relative to the solar system barycenter must be calculable
from the available ephemeris data. Typically ephemeris data
are made available by loading one or more SPK files using
cspice_furnsh.
- If non-inertial reference frames are used, then PCK
files, frame kernels, C-kernels, and SCLK kernels may be
needed.
- In some cases the observer's state may be computed at times
outside of `cnfine' by as much as 2 seconds; data required to
compute this state must be provided by loaded kernels. See
-Particulars for details.
Such kernel data are normally loaded once per program run, NOT
every time this routine is called.
1) The kernel files to be used by this routine must be loaded
(normally using the Mice routine cspice_furnsh) before this
routine is called.
2) This routine has the side effect of re-initializing the
coordinate quantity utility package. Callers may
need to re-initialize the package after calling this routine.
MICE.REQ
GF.REQ
SPK.REQ
CK.REQ
TIME.REQ
WINDOWS.REQ
None.
J. Diaz del Rio (ODC Space)
E.D. Wright (JPL)
-Mice Version 1.1.0, 03-NOV-2021 (EDW) (JDR)
Updated header to describe use of expanded confinement window.
Edited the header to comply with NAIF standard. Added
example's meta-kernel.
Added -Parameters, -Exceptions, -Files, -Restrictions,
-Literature_References and -Author_and_Institution sections.
Eliminated use of "lasterror" in rethrow.
Removed reference to the function's corresponding CSPICE header from
-Required_Reading section.
-Mice Version 1.0.2, 18-NOV-2014 (EDW)
Edited -I/O section to conform to NAIF standard for Mice
documentation.
-Mice Version 1.0.1, 05-SEP-2012 (EDW)
Edit to comments to correct search description.
Minor header edit "cosin" -> "cos".
Edit to Example description, replaced "intercept" with
"sub-observer point."
Header updated to describe use of cspice_gfstol.
-Mice Version 1.0.0, 15-APR-2009 (EDW)
GF subpoint coordinate search
|